【FPGA/verilog -入门学习15】vivado FPGA 数码管显示

1，需求：使用xc720 开发板的8个数码管显示12345678

2，需求分析：

75hc595

1，74hc595驱动，将串行数据转换成并行输出。对应研究手册

2，发送之前将要发的数据，合并成高8位:SEG,低8位：SEL, 结合testbanch查看波形，使用测试代码验证显示。

 //实现承有数码管显示1
`timescale 1ns/1ps
module vlg_74hc595_v(
    input i_clk,
    input i_rest_n,
    input [15:0]i_data,
    output reg o_ds,
    output reg   o_shcp,
    output reg   o_stcp
    );

//parameter i_sel = 8'b1111_0000; 
//parameter i_seg = 8'b1000_0000;

wire clk_25m;
wire clk_12r5m;
wire clk_100m;
wire locked;

  clk_wiz_0 clk_div_inst
   (
    // Clock out ports
    .clk_out1(clk_25m),     // output clk_out1
    .clk_out2(clk_12r5m),     // output clk_out2
    .clk_out3(clk_100m),     // output clk_out3
    .reset(~i_rest_n), // input reset
    .locked(locked),       // output locked
   // Clock in ports
    .clk_in1(i_clk));      // input clk_in1
     
 
//assign i_data[15:8] = i_seg;//seg7,seg6,seg5,seg4,seg3,seg2,seg1,seg0
//assign i_data[7:0] = i_sel;//s7,s6,s5,s4,s3,s2,s1,s0

reg [4:0]r_cnt;//16次计
//产生o_ds 信号
always @(posedge clk_12r5m) begin
if(!i_rest_n) begin
    o_ds <= 0;
    r_cnt <= 0;
end
else if(locked & r_cnt < 16)  begin
    o_ds <= i_data[15-r_cnt];
    r_cnt <= r_cnt + 1;
end
    else  begin r_cnt <= 0; o_ds <= 0; end
end

//产生o_shcp
 
always @(negedge clk_25m)   begin
    if(!i_rest_n) o_shcp <= 0;
    else if(r_cnt== 0) o_shcp <= 0;
    else  o_shcp <= ~o_shcp;
end
 
//产生o_stcp
always @(negedge clk_25m)   begin
    if(!i_rest_n) o_stcp <= 0;
    else if(r_cnt== 16 && o_shcp) o_stcp <= 1;
    else  o_stcp <= 0;
end
endmodule

分频

1，数码管以1Khz 切换1~8个数码管状态。 数码管刷新频率位 1KHZ/8 = 125hz/8ms 刷新一次

2，74hc595 更新bit 速率 12.5Mhz shcp

 //实现分屏，12.5M，50K
`timescale 1ns/1ps
module vlg_div(
    input i_clk,
    input i_rest_n,
    output o_clk_12r5m,
    output o_clk_1khz   //50*20=1000
    );
//`define SIMU_FLGA
`ifdef SIMU_FLGA
localparam CLK_12R5M_MAX = 50_000_000/12_500_000 -1;
localparam CLK_1KHZ_MAX   = 10-1;

`else
localparam CLK_12R5M_MAX = 50_000_000/12_500_000 -1;
localparam CLK_1KHZ_MAX   = 50_000_000/1000 -1;
  
 `endif
 

//12.5M 计数使能
reg [3:0]r_cnt_12r5m;
always @(posedge i_clk) begin
if(!i_rest_n) r_cnt_12r5m <= 0;
else if(r_cnt_12r5m < CLK_12R5M_MAX) r_cnt_12r5m <= r_cnt_12r5m +1;
else r_cnt_12r5m <= 0;
end
assign o_clk_12r5m = (r_cnt_12r5m == CLK_12R5M_MAX) ?1:0;


//50K 计数使能
reg [19:0]r_cnt_1khz;
always @(posedge i_clk) begin
if(!i_rest_n) r_cnt_1khz <= 0;
else if(r_cnt_1khz < CLK_1KHZ_MAX) r_cnt_1khz <= r_cnt_1khz +1;
else r_cnt_1khz <= 0;
end

assign o_clk_1khz = (r_cnt_1khz == CLK_1KHZ_MAX) ?1:0;


endmodule

数据产生

1，当1kHZ 来临时，合并sel+seg = [15:0]data

2，合并前要将sel 转换成 0000_0001 即每一1 代表要选择的sel

3，合并前将数字转换成数码管 编码

 //实现将8个数码管的数值，以20ms 输出seg+sel 的值
`timescale 1ns/1ps
module vlg_data_generate(
    input i_clk,
    input i_rest_n,
    input i_clk_1khz,
    input [31:0]i_data,  //输入8个数码管的数值 ，每个数码管用4位表示，例如f:1111
    output reg[15:0]o_data_seg_sel //输出数码管的seg+sel 高8位seg，低8位sel
    );

//产生20ms 的 0-7 计数
reg [7:0]r_index; //0-7
always @(posedge i_clk) begin
    if(!i_rest_n) r_index <= 0;
    else if(i_clk_1khz) begin
        if(r_index < 7) r_index <= r_index + 1;
        else r_index <= 0;
    end    
end

//根据0-7 变换，取出对应的seg 的hex码
reg [3:0]r_hex;  
always @(posedge i_clk) begin
    if(!i_rest_n) r_hex <= 0;
    else
        case (r_index)
        4'd0: r_hex <= i_data[3:0];
        4'd1: r_hex <= i_data[7:4];
        4'd2: r_hex <= i_data[11:8];
        4'd3: r_hex <= i_data[15:12];
        4'd4: r_hex <= i_data[19:16];
        4'd5: r_hex <= i_data[23:20];
        4'd6: r_hex <= i_data[27:24];
        4'd7: r_hex <= i_data[31:28];
        default r_hex <=  0;
        endcase
end

//将hex 变成数码管显示
reg [7:0]r_seg;
always @(posedge i_clk) begin
    if(!i_rest_n) r_seg <= 8'b1111_1111;
    else 
        case (r_hex)
        4'h0:r_seg <= 8'b1100_0000;//c0
        4'h1:r_seg <= 8'b1111_1001;//f9
        4'h2:r_seg <= 8'b1010_0100;//a4 
        4'h3:r_seg <= 8'b1011_0000;//b0 
        4'h4:r_seg <= 8'b1001_1001;//99 
        4'h5:r_seg <= 8'b1001_0010;//92 
        4'h6:r_seg <= 8'b1000_0010;//82 
        4'h7:r_seg <= 8'b1111_1000;//f8 
        4'h8:r_seg <= 8'b1000_0000;//80 
        4'h9:r_seg <= 8'b1001_0000;//90 
        4'ha:r_seg <= 8'b1000_1000;//88 
        4'hb:r_seg <= 8'b1000_0011;//83 
        4'hc:r_seg <= 8'b1100_0110;//c6
        4'hd:r_seg <= 8'b1010_0001;//a1 
        4'he:r_seg <= 8'b1000_0110;//86 
        4'hf:r_seg <= 8'b1000_1110;//8e 
        default:r_seg <= 8'b1111_1111;//ff        
        endcase
end
    
    
//将sel和seg 按    i_clk_50hz组合输出
always @(posedge i_clk) begin
    if(!i_rest_n) o_data_seg_sel <= 0;
    else if(i_clk_1khz &i_clk) begin
         o_data_seg_sel[7:0] <=  (1 << r_index);  //0-7
         o_data_seg_sel[15:8] <= r_seg;
         end    
         else ;
end
    
endmodule

输入输出

测试代码使用localparam data 赋值形式

正式代码使用vio 输入

 //vlg design 显示数码箿
 
`timescale 1ns/1ps
module vlg_design(
    input i_clk,
    input i_rest_n,
    output  o_ds,
    output  o_shcp,
    output  o_stcp
    );

//parameter i_data = 32'h12345678; 
 
wire [15:0]w_data_seg_sel;
wire w_clk_12r5m;
wire w_clk_1khz;
wire[32:0] w_data;

vio_0 your_instance_name (
  .clk(i_clk),                // input wire clk
  .probe_out0(w_data)  // output wire [31 : 0] probe_out0
);


//
vlg_74hc595_v vlg_74hc595_v_inst(
.i_clk(i_clk),
.i_rest_n(i_rest_n),
.i_data(w_data_seg_sel),
.o_ds(o_ds),
.o_shcp(o_shcp),
.o_stcp(o_stcp) 

);


//


vlg_data_generate vlg_data_generate_inst(

.i_clk(i_clk),
.i_rest_n(i_rest_n),
.i_clk_1khz(w_clk_1khz),
.i_data(w_data),
.o_data_seg_sel(w_data_seg_sel) 
);

//


vlg_div vlg_div_inst(
.i_clk(i_clk),
.i_rest_n(i_rest_n),
.o_clk_12r5m(w_clk_12r5m),
.o_clk_1khz(w_clk_1khz) 
);

endmodule

xdc

set_property PACKAGE_PIN Y18 [get_ports i_clk]
set_property PACKAGE_PIN F15 [get_ports i_rest_n]
set_property IOSTANDARD LVCMOS33 [get_ports i_clk]
set_property IOSTANDARD LVCMOS33 [get_ports i_rest_n]



set_property IOSTANDARD LVCMOS33 [get_ports o_ds]
set_property IOSTANDARD LVCMOS33 [get_ports o_shcp]
set_property IOSTANDARD LVCMOS33 [get_ports o_stcp]
set_property PACKAGE_PIN M18 [get_ports o_ds]
set_property PACKAGE_PIN F4 [get_ports o_shcp]
set_property PACKAGE_PIN C2 [get_ports o_stcp]

测试结果

3，调试记录

2023年12月30日

问题：本想显示全1的，结果成这样

2023年12月31日

解决了，撸了一遍视频，找到原因是时钟频率的问题，我直接把数据传输的时钟用的 50M。应该是74HC595 不支持这么高。现在换成12.5M 正常了。

2024年1月2日星期二

1. 完成使用vio 实现vivado自动配置数码管显示

readme